Product Code:SAE J1942/1
Title:Qualified Hoses for Marine Applications
Issuing Committee:Hydraulic Hose And Hose Fittings Committee
Scope:Effective August 28, 1991, the SAE replaced the USCG as the listing agency for Marine Hose Assemblies. The previous USCG list was discontinued as of December 31, 1992, and is being replaced by this SAE listing, J1942-1.All products appearing on the USCG list as of December 31, 1992, may be carried over to the SAE J1942-1 provided they meet the new test requirements listed in SAE J1942.If your products comply, you may retain your listings with no additional testing. (Please note that the USCG has the authority to request and inspect your test results at their discretion.)The following list consists of hose data provided as of May 2003, and is for convenience in determining acceptability of nonmetallic flexible hose assemblies intended for usage under 46 CFR 56.60-25(c). Where the maximum allowable working pressure (MAWP) or type of fitting is not specified, use the manufacturer's recommended MAWP or type of fitting. This list has been compiled by SAE Staff from information provided by the manufacturers whose product listings appear in this document.Manufacturers wishing to list their products in this document shall:Successfully test their hose to the requirements of SAE J1942, Table 1.Submit a letter of certification to the SAE J1942 test requirements for each specific type of hose tested. All sizes should be included in the same letter which must also include all of the information necessary to make a SAE J1942-1 listing.The SAE will review the letter and may, at their discretion, request to see some, or all, of the test results. A copy of the submittal letter marked 驴Accepted For Listing驴 will be returned to the applicant and a duplicate copy sent to the USCG.The cutoff date for inclusion of a hose listing in the annual SAE Handbook is April 30, of the preceding year. However, listed hoses may be used on vessels as soon as the 驴Accepted For Listing驴 letter is issued by the SAE.Next publication of this listing is scheduled to take place on December 2003. If you wish to include additional hoses in the 2003 publication of this list, please submit your Certified List to SAE Headquarters by October 2003.

标准名称：	冲模钢板下模座 第3部分：中间导柱下模座
英文名称：	Steel-plate die holders of stamping dies—Part 3:Center-pillar die holders
中标分类：	机械 >> 工艺装备 >> 模具
ICS分类：	机械制造 >> 无屑加工设备 >> 模制设备和铸造设备
发布部门：	中华人民共和国国家质量监督检验检疫总局 中国国家标准化管理委员会
发布日期：	2009-04-02
实施日期：	2010-01-01
首发日期：	2009-04-02
作废日期：
主管部门：	国家标准化管理委员会
提出单位：	全国模具标准化技术委员会(SAC/TC 33)
归口单位：	全国模具标准化技术委员会(SAC/TC 33)
起草单位：	桂林电器科学研究所、桂林电子科技大学、杭州萧山精密模具标准件厂、佛山市南海区粤诚五金塑料模具有限公司、镇江船山模架厂
起草人：	翁史振、廖宏谊、张玉琴、梁达志、祁伟根、奉双
出版社：	中国标准出版社
出版日期：	2010-01-01
页数：	8页
计划单号：	20075658-T-469

GB/T 23562的本部分规定了冲模钢板下模座中间导柱下模座的尺寸规格和标记。
本部分适用于冲模滑动导向与滚动导向钢板下模座的中间导柱下模座。

没有内容

没有内容

下列文件中的条款通过ＧＢ／Ｔ２３５６２的本部分的引用而成为本部分的条款。凡是注日期的引用文件，其随后所有的修改单（不包括勘误的内容）或修订版均不适用于本部分，然而，鼓励根据本部分达成协议的各方研究是否可使用这些文件的最新版本。凡是不注日期的引用文件，其最新版本适用于本部分。
ＪＢ／Ｔ８０５０　冲模模架技术条件
ＪＢ／Ｔ８０７０—２００８　冲模模架零件技术条件